The Ultimate EMF and Vastu Remediation Tool

Q-Tape™ is made from a special metal alloy that is easily bendable and can be applied to virtually anything emitting EMFs. Q-Tape™ is easy to cut with scissors, and after peeling off the backing, its sticky surface makes it easy to apply to a surface. It can also be taken off a surface fairly easily if it needs to be repositioned and then replaced.

EMF Balancing
The current flowing through electrical wires has a net positive charge. Q-Tape™ has a strong negative charge. When a small amount of Q-Tape™ is placed inside an electric box, the yin (Q-Tape) and yang (electric current) become balanced and the walls in your home or apartment “turn on” with a nicely resonant, balanced polarity. When opposing polarities are combined such as these, they can release a virtual shower of shimmering, high energy bio-energetic resonance.

Polarity Balancing
Q-Tape™ is very unusual in that it has a highly negative polarity (most metals have a net positive polarity). This makes Q-Tape™ the perfect element to balance highly polarized electrical currents which saturate all the walls of your home.

Electrical Circuit Breaker Box
To balance the EMF stress in your home (or office) due to A/C current, open the circuit breaker box and place one 3-inch strip of Q-Tape™ horizontally above the switches inside your circuit breaker box. Then place a second 3-inch strip directly on top of it (so there are two layers).  Then place another 3-inch strip vertically on the left hand side of the switches and one horizontally at the bottom of the circuit breaker box below the switches.

More than one breaker box. If you have a large home (or office), you may have two (or more) circuit breaker boxes. If so, please do the same procedure (as above) on each box.

Swimming pool circuit breaker box. If you have a swimming pool, most likely you will have a small circuit breaker box for the pool. If so, please do the same procedure (as above) on this box.

Telephone/Cable Box
To balance the EMF stress from telephone/cable service in your home (or office), place one 3-inch strip of Q-Tape™ with a second 3-inch strip directly on top of it (so there are two layers) on the telephone/cable box. Place the double strip horizontally on the top side of the outer box within ½” to 1” to the front of the box.

Electrical Transformer Box
Place one set of two 3” strips (double layered) horizontally on the box about 1” away from the front top edge of the cover.

Cell Phone

• Regular cell phone: Place one set of two 1½  x  ¼ inch strips of Q-Tape™ (double layered) on top of  the battery area or on the underside of the battery cover lid that covers the battery area. Be sure to place a strip of gaffers’ tape over the Q-Tape™.

• I-Phone and Blackberry cell phone: Place one set of two 1 ½ x ¼ inch strips (double layered) across the battery area or on the underside of the battery cover lid across the battery area. Be sure to place a strip of gaffers’ tape over the Q-Tape™. Then place two more sets of two directly below that set- making a total of three sets of two, doubled, strips on the back of the phone.

• Blue Tooth Ear Piece:  Place one set of two ½ x ¼ inch strips (double layered) on the ear piece. Be sure to place a strip of gaffers’ tape over the Q-Tape™.

Battery-Operated Devices

The Battery Strip : This is one ½-inch x ½-inch strip of Q-Tape™ placed directly over the top of another ½-inch x ½-inch strip of Q-Tape™ (so there are two layers). This should usually be covered with a small strip of gaffers’ tape* over the Battery Strip. *We recommend the Pro-Gaff  brand of gaffers’ tape.

• Notebook Computer: Place one Battery Strip over the middle of the battery area located on the bottom side of the computer. Then cover it with gaffers’ tape.

• Telephone base (that contains batteries): Place one Battery Strip over the battery area. Then cover with gaffers’ tape.

• Wireless home phone: Place one Battery Strip over the battery area of the phone.  Then cover it with gaffers’ tape.

• Electric Tooth Brush: Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Flashlight (large or small): Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Radio (which contains a battery): Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Computer Mouse (battery-operated only): Place one Battery Strip over the battery area underneath the mouse. Do not need to use the gaffers’ tape over it.

• Car Keys (any key that contains a battery): Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Clock (that contains a battery): Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Handheld Calculators (that contain a battery; this includes solar calculators which also contain a battery to store power: Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Camera: Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• TV Remote Controller: Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Massage Unit (that contains a battery): Place one Battery Strip over the battery area, cover it with gaffers’ tape.

• Toys (battery-operated): Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Walkie Talkie: Place one Battery Strip over the battery area. Then cover it with gaffers’ tape.

• Clarisonic Massage Unit (hand-held): Place one Battery Strip over the battery area located near the base of the hand-held unit on the side opposite the circular fibers. Then cover it with gaffers’ tape.

Exceptions for Battery-Operated Devices: The following are also battery-operated devices, but they require a different procedure:

• Radio-controlled clock  (that receives updates from the Colorado atomic clock):  Place a Battery Strip on the battery area (then cover with gaffers’ tape); place a second Battery Strip at the base of the unit (on the bottom & cover with gaffers’ tape.  Also place another Battery Strip on the base receiver unit (if there is one).

• UPS battery backup: 1½ inch x 1/4inch (double layered) for a 120 volt, 12 amp.

• Forklift: Place one set of two 3” strips (double layered) near the base of the large battery containment area to the rear.

• Hearing Aid (worn in the ear): Place a very small double strip of Q-TapeTM over the battery area of the hearing aid. Then cover it with a small amount of gaffers’ tape. Depending on the size of the hearing aid (some are very small), the double-strip may need to be very small (but it is still very important to do this). (For example, you may only be able to fit a ¼” x ¼” double strip on the battery area.) 
   

Vehicles

• Autos: Place two sets of two 3” strips (double layered) horizontal on the center of the front console above and below the radio.
• Large Trucks/Tractors: Place one set of two 3” strips (double layered) on the center of the front console and a second set in front of the overhead communications center.

Health Beyond Hype is licensed to distribute nutritional products manufactured by:
Premier Research Labs - Austin, TX.